Price Clear







Showing Gundam Parts product(s)

Showing 1 - 30 of 1123 products

img
SAVERM26.80

MG/HG Gundam Display Case

- HG MG Gundam Display Case,  suitable for any HG/RG/MG Gundam 
- Able to fit MG 1/100 Scale Gundam (without wing expansion and action base)
- Self assembly required + solid Strong support on the edge of the glass. 
- LED lightning 
- Item size : 26.5cm x 22cm x 3cm
- Case Dimension : 21.5cm (L) x 21cm (W) x 26cm (H)
- Able to fit MG model kits with action base.

RM38.20
img
SAVERM2.10

Gundam Accessories - Glow in the dark Sticker (10cm x 15cm)

Dimension: 10 cm x  15 cm 

Colors: Jade Color under daylight and, grow in the dark. 

Guide: 
1) Let the paper absorb light for 30 minutes to an hour (you may use torch light, or place under the sun), and it may grow it's light for a long time. 

2) Cut the paper to the right size to be used on the gundam, and stick on it, that's it. 

Tips: Stick the foil sticker included in the bandai original gundam box at the back of this product, and follow the size to cut the shape to ease the re-modelling.

RM3.90
img
SAVERM16.00

Bandai 1/144 , RG System Base 001 (Green Color)

This item is an accessory or set of accessories for Gundam models
Bandai brings even more goodies to the world of Gunpla with the addition of a new series of Gundam accessories called Builders Parts. This particular set is System Base #1, a great base to hold your 1/144 scale Gundam kits. The base is adjustable so it can accommodate wider kits and is molded all in one color.
  • Dimension: Height 18cm x Length 16cm x Width 10cm
  • Weight: 300g

RM36.00
img
SAVERM9.90

[Builder Parts] 1/144 MS Hand 02 (Zeon)

The hands in this set contain the rounded bulky design characteristic of Zeon mobile suits.

Set include:
- Fist (L&R) x2
- Flat hand (L&R) x2
- Hand for weapon (L&R) x2
- Top of hand x12

RM20.00
img
SAVERM10.90

[Builder Parts] 1/100 MS Spike 01

In the Detail-Up Parts, the Gundam modelling process has turned more enjoyable then ever.


With Gundam Part composition was conscious of compatibility is, of course, adopted the split parts considering the coloring. 
In addition, if you are using the material PS, you can easily cut, glue, and coloring. 

 - 3 types pedestal, with a combination of three needle, can be used in nine kinds of variations. 
 - The content of the commodity: three needle x, 3 x pedestal seed [x2 Sets] 

RM25.00
img
SAVERM8.90

Water Decal for MG 1/100 Blue Frame 2nd Revise Gundam

- Water Decal for MG 1/100 Blue Frame 2nd Revise Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM13.80

Mr Hobby Mr. Mark Softer

This is a softening agent for slide marks. It has the effect of closely adhering slidemarks to curved surfaces.

  • First, apply a quick drop to the area where the decal will go using the brush attached to the cap.
  • Apply decal over it.
  • Apply gentle pressure to the decal with a soft cloth, removing any excessive liquid and sticking the decal down fast.
  • The decal will stick perfectly, even on uneven or curved surfaces.
  • If air gets in between the decal and the model surface, after drying delicately prick the decal with a needle and insert Mr.MARK SOFTER through the resulting hole. The air will escape, and the decal will stick down firmly.
  • Capacity: 40ML

RM15.10
img
SAVERM11.00

Mr Hobby Mr. Mark Setter 40ML

  • Apply the mark setter to the position where decal is to be stuck.
  • Stick a slide mark
  • Spread it evenly and remove water with a swab, etc.
  • Apply the mark softer on it, remove water again.

In the past, Mr. MARK SOFTER was used simply to soften decals. 

However, now, using Mr. MARK SOFTER together with Mr. MARK SETTER (which gives decals greater adhesiveness) makes it much easier to affix decals to plastic models. 

First, the area to which the decal will be affixed is painted and the decal is applied. 

After air bubbles are removed by pressing on the decal with a cotton swab, a coating of Mr. MARK SOFTER is applied and allowed to dry. 

Because the decal now has greater adhesiveness, adhesive silvering (the floating and shiny quality of the clear parts of decals) can be firmly affixed to uneven surfaces. 

It is perfect even for poorly made decals from Eastern European models. 

Decals have better adhesiveness if the painted surface is prepared to have a glossy appearance, and they gain an appearance that suggests they were drawn by hand.

RM17.90
img
SAVERM4.70

Twin Base Gundam Stand - Suitable for 1/44 and SD (Black)

Basic Gundam Stand for HG 1/144 scale or SD gundam (Black)


- Suitable for BB, SD, SD Ex-Standard
- Can fit 2 Gundams 

RM5.20
img
SAVERM21.20

PG/MG Gundam Display Case

- PG Gundam Display Case,  suitable for any PG Gundam (without wing expansion and action base)
- PG 1/60 Scale Gundam (without wing expansion and action base)
- Self assembly required + solid Strong support on the edge of the glass. 
- Case Dimension : 20cm (L) x 26cm (W) x 42cm (H).
- Able to fit MG model kits with action base.

RM53.80
img
SAVERM8.90

[Bandai] Gundam HG Action Base 2 (Black)

A display stand for holding 1/144 scale and SD Gundam models, includes various adapters and holders to fit almost any 1/144 Gundam kit only! Assembles required! Larger than 1/144 model kits may require larger action base.

RM20.00
img
SAVERM8.90

[Bandai] Gundam HG Action Base 2 (Gray)

A display stand for holding 1/144 scale and SD Gundam models, includes various adapters and holders to fit almost any 1/144 Gundam kit only! Assembles required! Larger than 1/144 model kits may require larger action base.

RM20.00
img
SAVERM8.90

[Bandai] Gundam HG Action Base 2 (Red)

A display stand for holding 1/144 scale and SD Gundam models, includes various adapters and holders to fit almost any 1/144 Gundam kit only! Assembles required! Larger than 1/144 model kits may require larger action base.

Special designed for GN Drive Tau-based units from Mobile Suit Gundam 00 and HGUC-100/199.

RM20.00
img
SAVERM6.10

Basic Gundam Stand for SD or BB Gundam (Green)

Mini action base for SD Gundam (Black Colour)


- This is a NON-Bandai Product.
- Easy to assemble
- Able to support small scale HG kit 

RM3.80
img
SAVERM8.90

[Bandai] Gundam HG Action Base 2 (Green)

A display stand for holding 1/144 scale and SD Gundam models, includes various adapters and holders to fit almost any 1/144 Gundam kit only! Assembles required! Larger than 1/144 model kits may require larger action base.


Special designed for GN Drive-based units from Mobile Suit Gundam 00 and HGUC-178.

RM20.00
img
SAVERM6.10

Basic Gundam Stand for SD or BB Gundam (Red)

Mini action base for SD Gundam (Black Colour)


- This is a NON-Bandai Product.
- Easy to assemble
- Able to support small scale HG kit 

RM3.80
img
SAVERM6.10

Basic Gundam Stand for SD or BB Gundam (Blue)

Mini action base for SD Gundam (Black Colour)


- This is a NON-Bandai Product.
- Easy to assemble
- Able to support small scale HG kit 

RM3.80
img
SAVERM7.40

Tamiya Mark Fit 40ML

【 Perfect Decal Application 】   


Mark Fit enables perfect decal applications. It softens decals so they can easily fit to uneven, rounded, and matt finish surfaces of plastic models while increasing adhesion. The bottle's cap comes with a convenient brush. 1 bottle contains 40ml.

-  ‰ªHow to use -  ‰«
1. Apply Mark Fit to the model where decal is applied.
2. Place decal on the model.
3. Position decal by an wetting finger.
4. Press decal down gently with a soft cloth or cotton swab until excess water is gone.
5. Apply Mark Fit over the decal, then press down gently with a soft cloth or cotton swab.
6. Allow the decal to completely dry.

RM18.50
img
SAVERM8.90

Water Decal for HG 1/144 Gundam Heavyarms EW

- Water Decal for HG 1/144 Gundam Heavyarms EW
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM9.90

HD 1/144 MS MS EFFECT 01

Effect parts for recreating the scenes.

2 kinds of beam sabers and 2 kinds of nozzle effects are included.
2 sets of nozzle effect x2 and beam saber x2

For scale 1/144

RM20.00
img
SAVERM10.98

[Builder Parts] Non Scale MS Sword 01


Includes two long swords, two short swords, and connectors.
Can use for 1/144 or 1/100 

RM25.00
img
SAVERM20.90

RG Strike Freedom Wing of Light (Wing Accessories)

  • This package contains 'light' wing effect for 1/144 RG strike freedom gundam only.
  • RG 1/144 Strike Freedom Gundam is not included in this package and sold seperately.
  • Initial released comes with 8 pieces of Dragoon effects in the package.
  • THIS IS NON-BANDAI PRODUCT.

RM12.00
img
SAVERM7.90

[Bandai] MG/HG Action Base 1 Zeon Ver.

Original Bandai Action Base

Yellow base is molded in the shape of the Zeon insignia. 
Base arm is shorter than the standard model. 
Designed for the MS-06 Zaku II and other Zeon units. 
Suitable for SD, HG and MG Gunpla, assemble required.


RM40.00
img
SAVERM16.00

Bandai 1/144 , RG System Base 001 (White Color)

This item is an accessory or set of accessories for Gundam models
Bandai brings even more goodies to the world of Gunpla with the addition of a new series of Gundam accessories called Builders Parts. This particular set is System Base #1, a great base to hold your 1/144 scale Gundam kits. The base is adjustable so it can accommodate wider kits and is molded all in one color.

  • Dimension: Height 17.3cm x Length 16.2cm x Width 10 cm
  • Weight: 300g

RM36.00
img
SAVERM14.88

HG Strike Gundam Metal Blade Part

  • HG Strike Gundam metal knife part
  • This unit consists of the metal knife only, no other model kit included.
  • More precise photo to come after photographer done capture the metal blade.

RM15.10
img
SAVERM9.90

[Builder Parts] 1/144 MS Spike 02

[Builder Parts] 1/144 MS Spike 02


Includes:
4 Different Spikes x 2 each
Base Seed x 8

Item Size / Weight 24.4 x 17 x 2.3 cm / 30g

RM20.00
img
SAVERM8.90

Water Decal for MG 1/100 00 QAN[T] Gundam

- Water Decal for MG 1/100 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal HG Beargguy III

- Water Decal for HG BEARGGUY III water decal
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal HG 1/144 00 QAN[T] Gundam

- Water Decal for HG 1/144 00 QAN[T] Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00
img
SAVERM8.90

Water Decal for MG 1/100 GAT-X103 BUSTER Gundam

- Water Decal for MG 1/100 GAT-X103 BUSTER Gundam
- Not pre-cut
- Best use with Mr. Hobby Mr. Mark Setter / Softer
- 11 cm x 15 cm

Tools:

* Decals
* Mr. Mark Setter (optional)
* Mr. Mark Softer (optional)
* Water
* Cotton buds
* Tweezers
* Paper towel
* Pen Knife

Instructions :
1. Again, cut out the design you want from the decal sheet
2. Using a pair of tweezers/forceps, pick up the decal you cut out and dip in water for roughly 8 seconds. I found that Bandai water-slide decals need less time, maybe 4-6 seconds while custom decals might take longer than 8 seconds. The purpose of this step is to detach the decal from the decal sheet.
3. Using a cotton bud dipped in water, gently ‘tease’ the decal away from the decal sheet and onto your gunpla. If the decal won’t budge from the decal sheet, dip in water for a couple more seconds.
4. Once the decal is on your gunla, you can still adjust or reposition the decal. Once you’re satisfied with the position, use the dry end of the cotton bud to gently roll over decal to absorb extra water.


Water slide decals are activated by water. So it's important to store them away from liquid. 

RM9.00

Showing 1 - 30 of 1123 products